Heating


There are two major areas to look at for controlling the temperature of our house and immediate environment. the first of these could be called ‘active’, where there is a direct energy input such as a wood fire, electric heater or air conditioner. This is where one sees the costs of running the house increase with use.

To reduce the need for the active component of climate control and maximise its effectiveness, we look to the second division, the ‘passive’ part.

Consider this, before we go much further – the best insulator is still, motionless air. Keep that in mind, and you will find what follows to be quite easy.

 

Airflow

Th heat a room, we either allow the heat to enter (as in letting sunlight come in through a window) or trap the heat that is already in the room and prevent it leaving.

The easiest way to do this is simply to block off gaps that allow uncontrolled airflow. Gaps around and under doors or around window frames, open vents and fireplaces, even exhaust fans can let heat escape or cold enter.

Door seals

The quickest and easiest way to seal doors and windows is to use the foam door seal strips that go around the window or door frame and stop them from leaking. There are also the under door seals, or ‘weather strips’,that seal the gap under the door. They are also called ‘draught excluders’ and range from elaborate, hinged devices to the old fabric ‘snake’. Ultimately, they do the same job.

Sealing around the door of our lounge last year gave almost instant benefits with an average of a 2 degree rise in temperature in that room!.That meant that we could lower the thermostat on the heater by 2 degrees for the same level of comfort (or take off one layer of extra clothing!).

In summer, we noticed a reduction in warm air entering through the doorway too.

Windows

A lot of heat enters or leaves a room through the glass of the windows or gaps in the frames. We have sash windows, which are notorious for not fitting properly.

One quick and very cheap way to insulate windows is to use bubble wrap. It’s a cheap and easy to install insulator that can make a very big difference. Not only do you add a layer of plastic to the glass, but the little bubbles are little pockets of still air (remember, it’s the best insulator).

One of the joys of using bubble wrap is that to install it, you only need to cut it to size, then wipe the window with plain water. Press the bubble wrap to the glass and hey presto! It sticks.

To stop airflow through the cracks where the windows meet, I just use plain old sticky tape. It’s cheap, and it works. Add another degree of temperature to that room!

By far the most effective way to stop heat and air loss to room is to have curtains. We made our own using a layer of quilt fabric and 100% block out fabric backing. It was a bit pricey, but I got the quilt fabric for free, so that made up for it cost of the block out. We didn’t buy the block out all at once, either. We did one room at a time, as finances permitted.

When fitting your curtains, be aware of something called ‘thermocycling’.

Thermocycling is when heated or cooled air flows past a window. For example, in winter, the warm air at the top of the room is cooled when it hits the cold glass, then falls as it is cooled, reaching the floor. This displaces air at that level. As this air is warmed, it rises, then hits the cold glass and falls. You get the picture…

So, how to stop thermocycling? It’s as easy as blocking off the top and bottom of the curtains. When fitting them, make sure they reach the floor. That stops the hot or cold air flowing at bottom.

For the top, install pelmets. They’re the boxes that you see,above some windows. We took a cheap shortcut and layed wide canvas strips along the top of the curtains where the pleats are. These we secured with safety pins. It’s cheap and it works.

So, door seals, floor length curtains and pelmets and bubblewrap. That’s a winning trifecta, that will allow you to use your heating appliances much less. That saves money, and reduces the amount of greenhouse gasses generated.

Other

There are other ways to help keep the heat in. They include –

Roof and ceiling insulation.   Thats expensive, but well worth the investment. You can get by by using the commercial stuff and installing it yourself (a horrible, horrible job!) room by room. start with the main living room and main bedrooms. It’s your living space that youre heating, afterall. later, when finances permit, move to other rooms.

Cornices and skirting boards.   These often move as the house shifts and can open up some quite large gaps. Ideally, seal them with caulk or silicon sealant or similar, but as a stop gap measure, push some fabric or paper into the hole to temporarily seal it.

Manhole cover.   The access cover to the roof cavity can be loose and poorly fitting. See if you can adjust it, or, as we did, put a sheet of cardboard or coir flute over it during the cold weather.

Exhaust fans.   Bathroom and kitchen exhaust fans are wide open to the roof cavity, letting heat escape continuously, even when not in use.You can reduce the heat loss from living spaces by closing the bathroom or kitchen door, but there are caps with pivoting lids that are easy to install on top of the exhaust fan. These allow air to flow when the fan is on and settle back over the hole when it stops.

Aircon vents.   Some of these close, other varieties are purely aesthetic. In theory, the airconditioner is sealed and the conduit is air tight and insulated. This may not be the case with older units which will allow air to flow all the time. Either invest in closing covers or use cardboard to cover them. Some folks take them down and put newspaper or magazines inside to do the same job. We used coir flute sticky taped across the hole.

Wall vents.    Ours’ is an older, double brick home with 2 wall vents in each room on both the inside and outside bricks. This is  to prevent dampness from building up in the wall cavity, but is a case of overkill. We close off one of each of the inside vents in each room wtih a square of cardboard and Blu Tack. This reduces heat loss because the vents are near the ceiling, where the hot air goes, but still allows some flow throughout the cavity.

Power points.   This is  something that I’ve only recently found out about. Some powerpoint plates allow air to flow through the holes where the plugs go. As I found from experience, the draught from these can be quite strong. We now keep them sealed with those little plastic plugs that you can buy to keep kids from poking things in to the powerpoint. Alternatively you  can just leave things plugged in (but turned off wehn not in use) or cover the plug holes with stciky tape.

 

We’ve done all of the above and, on average have reduced our winter heating from 2 X 1000W and one 1200W heater down to one 1000W heater and a second that is set down to 400W. That’s a saving of 1800W per hour!

The average indoor overnight temperature drops to a minimum of 11-12 degrees Cenrigrade, whereas before, when the heaters were off, it would drop to 8 C.

As the house is quite long, we had a temperature difference between the lounge and the bedroom of 4 C. Now it’s only 1 C. That means that we don’t need a heater in the master bedroom at all!

Thats a massive saving over winter!

Advertisements